LM74700MDDFREP

Texas Instruments
595-LM74700MDDFREP
LM74700MDDFREP

製造商:

說明:
熱插拔電壓控制器 Enhanced low IQ ideal diode controller 8-SOT-23-THIN -50 to 125

ECAD模型:
下載免費的庫載入器,為ECAD工具轉換此文件。瞭解更多關於 ECAD 型號的資訊。

庫存量: 1,357

庫存:
1,357 可立即送貨
最少: 1   多個: 1
單價:
NT$-.--
總價:
NT$-.--
估計關稅:
包裝:
完整捲(訂購多個3000)

Pricing (TWD)

數量 單價
總價
零卷 / MouseReel™
NT$177.82 NT$177.82
NT$135.66 NT$1,356.60
NT$125.12 NT$3,128.00
NT$113.56 NT$11,356.00
NT$108.12 NT$27,030.00
NT$104.72 NT$52,360.00
NT$99.28 NT$99,280.00
完整捲(訂購多個3000)
NT$96.90 NT$290,700.00
† NT$215.00 MouseReel™費用將加入您的購物車內並自動計算。所有MouseReel™訂單均不能取消和不能退換。

商品屬性 屬性值 選擇屬性
Texas Instruments
產品類型: 熱插拔電壓控制器
RoHS:  
Controllers & Switches
2.3 A
65 V
3.2 V
1 Channel
80 uA
- 50 C
+ 125 C
SMD/SMT
SOT-23-THIN-8
Reel
Cut Tape
MouseReel
Yes
品牌: Texas Instruments
組裝國家: Not Available
擴散國: Not Available
原產國: PH
開發套件: LM74700DDFEVM
輸入/電源電壓 - 最大值: 65 V
輸入/電源電壓 - 最小值: 3.2 V
濕度敏感: Yes
產品類型: Hot Swap Voltage Controllers
系列: LM74700
原廠包裝數量: 3000
子類別: PMIC - Power Management ICs
找到產品:
若要顯示類似商品,請選取至少一個核選方塊
至少選中以上一個核取方塊以顯示在此類別中類似的產品。
所選屬性: 0

此功能需要啟用JavaScript。

CNHTS:
8542399000
CAHTS:
8542310000
USHTS:
8542310030
ECCN:
EAR99

LM74700-Q1理想二晶體控制器

Texas Instruments LM74700-Q1理想二晶體控制器可搭配外部N通道MOSFET以20mV前向壓降實現低損失逆向極化保護。LM74700-Q1具有3.2V至65V的寬電源輸入範圍,允許控制包括汽車電池系統在內的許多流行DC匯流排電壓。3.2V輸入電壓支持格外適用於汽車系統內的嚴寒曲柄要求。該裝置可承受和保護地址-65V的負電源電壓負載。

LM5060 High-Side Protection Controllers

Texas Instruments LM5060 High-Side Protection Controllers with Low Quiescent Current offers intelligent control of a high-side N-channel MOSFET during normal on/off transitions and fault conditions. The constant rise time of the output voltage results from the inrush current control. Both an Input UVLO (with hysteresis) and a programmable input OVP are provided, with an enable input offering a remote on or off control. The initial start-up VGS fault detection delay time, the transition VDS fault detection delay time, and the continuous over-current VDS fault detection delay time is programmed from a single capacitor. The MOSFET is latched off until either the enable input, or the UVLO input is toggled low and then high when a detected fault condition persists longer than the allowed fault delay time.